Name: Faria Beede Instruments® - Kronos Series 3.37" Spun Aluminum Dial/Polished Stainless Steel Bezel In-Dash Mount Tachometer Gauge
Brand: Faria Beede Instruments
SKU: mpn4795348168
Price: 236.32 USD
Availability: OutOfStock
Rating: 5 (2 reviews)

Specifications

Operating Temperature	-4°F to +158°F (-20°C to +70°C)
Storage Temperature	-22°F to +185°F (-30°C to +85°C)
Operating Voltage	11.5 to 16 volts
Nominal Voltage	14.2 volts
Current Consumption	< 100 mA, without illumination
Mounting Bracket	Mounting clamp. Clamping range 0 -.8" (0-20 mm)
Torque	5 to 7 inch pounds (.57 - .80 Nm)
Mounting Hole	3-3/8” (85 mm) for 4" Instrument

Features

SystemCheck® warnings: No Oil, Engine Overheat, Check Engine, Low Oil
Suzuki Monitor® warnings: Check Engine, Temperature, Oil Level, Rev. Limit
OBD warnings: OBD Alert
Engineered to high standards
High-grade design delivers extended lifespan
Made with premium materials

Product Details

Kronos Series 3.37" Spun Aluminum Dial/Polished Stainless Steel Bezel In-Dash Mount Tachometer Gauge (39005) by Faria Beede Instruments®. Measurement Limit: 7000 RPM. Engine Type: All Outboards. Polished Stainless Steel Bezel, Flat Glass Lens, Perimeter Lighted Spun Aluminum dial with Gold and Black graphics. Gold increments and Logo on dial are Embossed. All instruments include two piece Newport Pointer with White Hub. Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12V DC, Ground and one of the signal sources listed above. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine. Available with SystemCheck®. Suzuki Monitor® or OBD warning systems.

Faria Beede Instruments® - Catalog Made In USA Faria Beede Instruments Authorized Dealer

Brand:

Faria Beede Instruments

Part Number:

39005

UPC:

759266390058

Warranty

During the initial warranty period of 36 months from the date of the original retail purchase (12 months on fog resistant lens, Fuel Manager, Depth Sounder, Commander-Speedo, Commander-Tach, Pilot I, Pilot II, MG1000, MG2000 and MG3000 and 24 months on Senders, Transducers, Triducers and Smartducers), any instrument that fails due to defects in materials or workmanship will be repaired or replaced at Faria Beede Instruments’ option.

Upon completion of repair or replacement the applicable initial warranty period of 36/12 months is renewed.

Any damage to an instrument resulting from natural disasters, misuse, neglect, accident, misapplication, improper installation, unauthorized repair or alteration, and instruments purchased prior to March 1, 1985 are not covered by this warranty.

Faria Beede Instruments, Inc. expressly disclaims any liability for incidental of consequential damage caused by product defects. Some states do not allow the exclusion or limitation of consequential damages, so the above may not apply to you. The Warranty herein is in lieu of any other expressed warranty of merchantability or fitness or any other obligation on the part of Faria Beede Instruments, Inc., or the seller. All implied warranties are limited to the initial 36 month period. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you also have other rights which vary from state to state.

Reviews

(2)

Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.

1-2 of 2 Reviews

Sort by

5 of 5

G3 Angler V16

Factory didn’t install one and this was as close of a match I could find to my factory gauges. Works and will help me with proper maintenance. FB has great support and made in United States

Faria Beede Instruments® 19020 - Kronos 2" Spun Aluminum Dial/Polished Stainless Steel Bezel In-Dash Mount Hourmeter Gauge

Posted by David / August 31, 2020

5 of 5

G3 Angler V16

Factory didn’t install one and this was as close of a match I could find to my factory gauges. Works and will help me with proper maintenance. FB has great support and made in United States.

Faria Beede Instruments® 19020 - Kronos 2" Spun Aluminum Dial/Polished Stainless Steel Bezel In-Dash Mount Hourmeter Gauge

Posted by David / August 31, 2020

Questions and Answers

(0)

If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!