Product Details

PL-65 5-1/2" Setback High Speed Hydraulic Jack Plate without Gauge by CMC®. The dependable, self-contained and water proof hydraulic actuator has a maximum lifting capacity of 7853 pounds of thrust. More than any other transom jack. You will have no problem lifting even a V-6 300 hp max. motor at full throttle.

Specifications

Setback: 5-1/2"

Features

Full stroke in 8 seconds
Features Of Patented Hydraulic Power-Lift (U.S. Patent 4,482,330)
Made of 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners
Ideal for fresh or salt water use
No welds or castings to break
Designed to offer exceptional performance and reliability
Made using high-quality materials for long-lasting service life
Proven to live up to the most demanding marine conditions
Engineered to meet or exceed the highest quality standards

The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks. The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminates the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has twice the lifting capacity than other transom jacks on the market. It contains a no-leak seal and wiper that keeps dirt and water out of the working parts. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.

The patented roller design means less friction, longer wear, less maintenance, and virtually no binding problems which are common with other transom jacks. The roller assembly contains a stainless steel 3/4" pin with aluminum-bronze alloy rollers. The roller is highly impact resistant, corrosive resistant, and has a high load carrying capacity. This patented design virtually eliminates any chance of binding which is common with other transom jacks.

The PL-65 is rated for V-6 motors and smaller and gives you 5" of vertical travel with 1-1/2" of adjustment on the motor bracket and 1-1/2" of adjustment on the transom bracket. A total of 8" of possible adjustment.

Since 1956, CMC® has produced products for marine, oilfield, industrial computer, and industrial hydraulic markets. CMC has led the marine market with jack plates for over 30 years and with aftermarket tilt and trim units for over 20 years. Now all hydraulic units are driven with patented hydraulic actuator. CMC was the originator and pioneer of providing a self-contained hydraulic jack plate. CMC utilizes the finest computerized machinery available for precision and speed. This enables to manufacture top quality products at a very competitive price, giving the consumer many years of trouble free service at the best price. Testing procedures are implemented on each item to meet certain parameters before any unit is packaged for shipment. This quality control is done to ensure that CMC maintains the lowest service-repair record possible.

Brand:

CMC

Part Number:

13022 65302

Warranty

CMC Marine, Inc. warrants to the first retail purchaser of its products that CMC Marine, Inc. will replace or repair the product, at its sole discretion, if any defects in material or workmanship are reported within the applicable warranty periods set out below from the date of the first retail purchase, subject to the remedies, exclusions, and limitations in this Limited Warranty

CMC hydraulic jack plates, CMC Tilt, and Trim units: Hydraulic Actuator mechanism - 1 year
CMC hydraulic jack plates, manual jack plates and CMC Tilt, and Trim units: frame structure assembly – 5 years
All other CMC Marine, Inc. Products - 1 year

Other Limitations

Except as set forth herein, there are no other warranties, either express or implied, provided by CMC Marine, Inc. on this product. All other warranties, express or implied, including implied warranties of fitness and merchantability, are expressly excluded. CMC Marine, Inc. further disclaims any liability for economic loss arising from claims of product failure, negligence, defective design, manufacturing defect, failure to warn and/or instruct, lack of seaworthiness, and any other theory of liability not expressly covered under the terms of this limited warranty.

To the extent required by law any implied warranty is limited to the duration of the respective express limited warranties stated herein. To the extent allowed by law neither CMC Marine, Inc., nor the selling distributor, nor the selling retailer shall have any responsibility for loss of use of the product or the boat, loss of time, inconvenience, commercial loss or incidental and consequential damages. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not be applicable. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not be applicable. This warranty gives the owner specific legal rights, and the owner may also have other rights which vary from state to state.

Sole Remedy

In no event shall any repair or replacement under this Limited Warranty exceed the fair market value of the product as of the date of the owner’s claim. The remedy of repair or replacement of parts or materials found to be defective in factory materials or workmanship covered by this limited warranty shall constitute the owner’s sole and exclusive remedy against CMC Marine, Inc. for any claims whatsoever of economic loss resulting from product failure.

The terms and conditions contained in this limited warranty may not be modified, altered or waived by any action, inaction, or representations, whether oral or in writing, except upon the express, written authority of a management level employee of CMC Marine, Inc.

This Limited Warranty does not apply to the following items:

Any CMC Marine, Inc. products used in other applications than on pleasure boats, including but not limited to non-marine use or use on boats which are utilized for racing or commercial purposes
Ancillary equipment used or associated with CMC Marine, Inc. products, including but not limited to, batteries, fuses, switches, wiring, electric light bulbs, lamps, or sealed beam units
Any product damaged by accident, acts of nature, improper installation, unreasonable or improper use, lack of proper maintenance, unauthorized repairs or modifications, abuse, normal wear or tear, or other causes not arising from defects in materials or workmanship
Any expenses involved in the removal, reinstallation, or transportation of the product
Any product damaged by the failure of the owner to use, maintain, or store the product as specified in any instructions
Any product with discolocation or failure due to solar or chemical exposure
Any defect or repair requiring redesign of the CMC Marine, Inc. product, except pursuant to the recall provisions of the United States Federal Boat Safety Act of 1971 or the recall laws of any other foreign jurisdiction

Additional CMC Limited Warranty Terms:

This warranty means that only the parts that prove defective during the period of warranty will be repaired or replaced at CMC’ option.

Avoid tampering with the Hydraulic Actuator if a warranty claim is to be made. The warranty is void on any hydraulic actuator returned that shows signs that it has been dismantled or electrical cord set from the motor has been cut.

There are no warranties which extend beyond the description on the face hereof. No one has authority to make any representations concerning the operation of CMC units except those made in writing by CMC Marine, Inc.

This warranty does not apply for any racing applications or if damage occurs because of accident, improper handing or operation, abuse or misuse.

All liability for any incidental or consequential damage is expressly excluded from this warranty.

Reviews

(0)

Only authorized customers can leave a review on our website. We would love to know what you like or dislike about the product. Share your opinion on product quality, appearance, installation, and other characteristics.

CMC® - PL-65 5-1/2" Setback High Speed Hydraulic Jack Plate w/o Gauge

CMC® - PL-65 5-1/2" Setback High Speed Hydraulic Jack Plate w/o Gauge

Product Details

Specifications

Features

Related Links

Reviews